CFW500A01P6S2NB20G2, VFD, 0.25HP, 230V 1PH IN, 230V 3PH OUT, 1.6FLA
WEG CFW500G2 AC Drive, 0.25HP, 230V 1 PH Input, 230V 3 PH Output, 1.6FLA, IP20
Weight: 1.8 lbs.Made in: Brazil
CFW500A01P6S2NB20G2, VFD, 0.25HP, 230V 1PH IN, 230V 3PH OUT, 1.6FLA
WEG CFW500G2 AC Drive, 0.25HP, 230V 1 PH Input, 230V 3 PH Output, 1.6FLA, IP20
Weight: 1.8 lbs.Made in: Brazil
Specifications
WEG CFW500G2 AC Drive, 0.25HP, 230V 1 PH Input, 230V 3 PH Output, 1.6FLA, IP20
- Supply Voltage Models: 200-600V - Single-Phase or Three-Phase
- Rated Currents: 1.6 to 211A
- Controls: Vector (VVW), Scalar (V/F), Sensorless Vector or with Encoder and Permanent Magnet Motor Control (VVW PM)
- Built-in SoftPLC Function
- Pump Applications
- RS485 Port (Built-in on any Model of Plug-in Module)
- Plug-in Cards for Resource Expansion
- Free Programming Software: WEG WPS Software
- Optional Items:
- RFI Filter
- USB Communication Port
- Memory Card: allows Data Transfer (Parameters and SoftPLC) between Inverters, without the necessity to energize them
- Network Communication: CANopen, DeviceNet, Profibus-DP, RS232, RS485, EtherNET-IP, Modbus-TCP and Profinet-IO
General Specifications
| Power Supply | Voltage tolerance: 220-240VAC (-15% to + 10%) Single Phase Frequency: 50/60 Hz (48 Hz to 62 Hz) Phase unbalance: ≤3% of the rated phase-phase input voltage Overvoltages according to category III (EN 61010/UL 508C) Transient voltages according to Category III Maximum of 10 connections per hour (1 every 6 minutes) Typical efficiency: ≥97% Classification of mechanical conditions (vibration): 3M4 level |
| Input minimum-maximum voltage | 220-240 VAC Single Phase |
| Maximum Motor | 0.25HP/0.18kW |
| Rated current (HD) | 1.6A |
| Overload Capacity | 2.4A for 1 minute every 6 minutes |
| Installation and connection | |
| Environment conditions | Surrounding temperature: 14° - 122°F (-10° to 50°C) - IP20 For higher temperatures than the specifications above, it is necessary to apply 2% of current derating for each Celcius degree, limited to an increase of 50°F (10°C) Air relative humidity: 5% to 95% non-condensing Maximum altitude: up to 3,300ft (1,000m) - rated conditions 3,300ft to 13,200ft (1,000m to 4,000m) - 1.1% of current derating for each 330ft (100m) above 6,600ft (2,000m) (above the sea level) Pollution degree: 2 (according to EN 50178 and UL 508C), with non-conductive pollution. Condensation must not cause conduction of the accumulated residues |
| Control | |
| Method | V/F (scalar) VVW: voltage vector control Vector (sensor or sensorless) |
| Output frequency | 0 to 500 Hz, resolution of 0.015 Hz |
| Performance | |
| V/F Control | Speed regulation: 1% of the rated speed Speed variation range: 1:20 |
| VVW | Speed regulation: 1% of the rated speed Speed variation range: 1:30 |
| Vector (Sensorless) | Speed regulation: 0.5% of the rated speed Speed variation range: 1:100 |
| Vector (Sensor) | Speed regulation: 0.1% of the rated speed |
| Inputs | |
| Analog | 1 isolated input: 0 to 10 V or 0 to 20 mA or 4 to 20 mA Linearity error ≤0.25% Impedance: 100 kΩ for voltage input, 500 Ω for current input Programmable functions Maximum input voltage: 30 V dc |
| Digital | 4 isolated inputs Programmable functions: Active high (PNP): maximum low level of 15 V dc minimum high level of 20 V dc Active low (NPN): maximum low level of 5 V dc minimum high level of 9 V dc Maximum input voltage of 30 V dc Input current: 4.5 mA Maximum input current: 5.5 mA |
| Outputs | |
| Relay | 1 relay with NO/NC contact Maximum voltage: 250 V ac Maximum current of 0.5 A Programmable functions |
| Transistor | 1 digital sinking output Maximum voltage: 24 V dc Maximum current of 150 mA Programmable functions |
| Power supply | 24 V dc power supply maximum capacity: 150 mA 10V dc power supply maximum capacity: 2 mA |
| Safety | |
| Protection | Overcurrent/phase-phase short circuit Under/overvoltage at the power supply Motor overload Overtemperature on the power module (IGBTs) External fault/alarm Programming error |
| Operating interface (HMI) | |
| Built-in | 4 keys: run/stop, increment, decrement and LCD Display setting |
| Communication | |
| Fieldbus communication | RS485, RS232, CANopen, DeviceNet, Profibus-DP, Bluetooth or USB Port (via plug-in modules) |
| Protection degree | IP20 |
| Frame Size A | 6.22"H x 2.76"W x 5.84"D |
| Weight | 1.98lb |
